本文已被:浏览 2734次 下载 2887次
投稿时间:2014-05-12 修订日期:2014-05-14 录用日期:2014-05-16 网络发布日期:2014-10-15
投稿时间:2014-05-12 修订日期:2014-05-14 录用日期:2014-05-16 网络发布日期:2014-10-15
中文摘要: 分别采用直接氰化法、浮选—氰化法和碘化法处理某含铜难处理金矿,并考察了搅拌强度、浸出时间和矿浆温度对碘化浸金效果的影响。结果表明,采用直接氰化法在氰化钠用量为10 kg/t时,金浸出率为82%左右,铜浸出率为40%左右;利用浮选—氰化法得到的浮选精矿中金、铜品位分别为36.9 g/t和4.69%,金、铜回收率分别为57.41%和62.35%,浮选精矿中砷品位达到4.2%,浮选尾矿氰化金的浸出率为65.96%;碘化试验中金浸出率达到85.3%,铜浸出率低于1%。碘化法比较适宜处理该金矿,其最佳工艺条件为:搅拌强度400 r/min、浸出时间2 h、矿浆温度298 K。
Abstract:Gold was recovered from one copper-bearing and arsenic-bearing refractory gold ore by direct-cyaniding, flotation-cyaniding and iodide process, respectively. The effects of stirring intensity, leaching time and slurry temperature on gold leaching rate by iodide process were investigated. The results show that directly cyaniding leaching rate of gold and copper is 82% and 40% respectively. The flotation concentrate with Cu/Au grade of 4.69%/36.9 g/t and Cu/Au recovery of 62.35%/57.41% was obtained by bulk flotation. The flotation tailings were cyaniding leached with gold recovery of 65.96%. The leaching rate of gold is 85.3% and leaching rate of copper is 1% below in iodide process. The optimum experimental conditions for iodide process include stirring intensity of 400 r/min, leaching time of 2 h and slurry temperature of 298 K.
keywords: direct cyaniding leaching flotation and cyaniding iodination refractory gold ore leaching rate
文章编号: 中图分类号:TF 文献标志码:
基金项目:高等学校博士学科点专项科研基金项目(20100006110003)
引用文本:
袁喜振,孙春宝,李绍英,赵留成,李根壮,邓祥意,张炜,郭林中.某含铜难处理金矿提金试验[J].有色金属(冶炼部分),2014(11):43-47.
YUAN Xi-zhen,SUN Chun-bao,LI Shao-ying,ZHAO Liu-cheng,LI Gen-zhuang,DENG Xiang-yi,ZHANG Wei,GUO Lin-zhong.Experiment of Gold Recovery from Copper-bearing Refractory Gold Ores[J].Nonferrous Metals (Extractive Metallurgy),2014(11):43-47.
袁喜振,孙春宝,李绍英,赵留成,李根壮,邓祥意,张炜,郭林中.某含铜难处理金矿提金试验[J].有色金属(冶炼部分),2014(11):43-47.
YUAN Xi-zhen,SUN Chun-bao,LI Shao-ying,ZHAO Liu-cheng,LI Gen-zhuang,DENG Xiang-yi,ZHANG Wei,GUO Lin-zhong.Experiment of Gold Recovery from Copper-bearing Refractory Gold Ores[J].Nonferrous Metals (Extractive Metallurgy),2014(11):43-47.

关注微信公众号