###
有色金属(冶炼部分):2014,(7):14-16
←前一篇   |   后一篇→
本文二维码信息
码上扫一扫!
铜阳极泥氧压酸浸预处理工艺研究
钟清慎,贺秀珍,马玉天,刘玉强
(西安建筑科技大学 冶金工程学院,金川集团股份有限公司/贵金属冶炼厂/贵金属研究中心,金川集团股份有限公司,金川集团股份有限公司)
Study of Oxygen Pressure Acid Leaching Pretreatment Technology for Copper Anode Slime
ZhONG Qing-Shen,HE Xiu-Zhen,MA Yu-Tian and LIU Yu-Qiang
(School of Metallurgical Engineering,Xi,an University of Architecture and Technology,Xi,an Shanxi Province,,,)
摘要
图/表
参考文献
相似文献
本文已被:浏览 2862次   下载 2843次
投稿时间:2014-01-04     修订日期:2014-01-10     录用日期:2014-01-13     网络发布日期:2014-06-23
中文摘要: 研究某铜阳极泥氧压酸浸工艺条件,考察硫酸初始浓度、温度、时间、液固比、压力等对金属浸出的影响。结果表明,当控制浸出硫酸初始浓度130~150 g/L、温度155~165 ℃、时间6~8 h、液固比5∶1、压力1.0~1.5 MPa时,酸浸渣率为55%~60%,碲浸出率为85%~90%,镍、铜浸出率均在99%以上。
中文关键词: 铜阳极泥  氧压酸浸  碲  硒  浸出率
Abstract:Oxygen pressure acid leaching process for copper anode slime was studied. The effects of initial concentration of sulfuric acid, leaching temperature and time, ratio of liquid to solid (L/S), and pressure on leaching were investigated. The results show that leaching slag rate is 55%~60%, tellurium leaching rate is 85%~90%, and leaching rate of nickel and copper is 99% above under the optimum conditions including initial concentration of sulfuric acid of 130~150 g/L, temperature of 155~165 ℃, time of 6~8 h, L/S=5∶1, and leaching pressure of 1.0~1.5 MPa.
文章编号:     中图分类号:TF843.5;TN304.1    文献标志码:
基金项目:金川集团股份有限公司“十一五”、“十二五”重点建设项目(2121010)
引用文本:
钟清慎,贺秀珍,马玉天,刘玉强.铜阳极泥氧压酸浸预处理工艺研究[J].有色金属(冶炼部分),2014(7):14-16.
ZhONG Qing-Shen,HE Xiu-Zhen,MA Yu-Tian,LIU Yu-Qiang.Study of Oxygen Pressure Acid Leaching Pretreatment Technology for Copper Anode Slime[J].Nonferrous Metals (Extractive Metallurgy),2014(7):14-16.

我们一直在努力打
造,精品期刊,传
播学术成果

全国咨询服务热线
86-10-63299752/63299758

联系我们

电话:010-63299752/63299758

传真:010-63299744

QQ:XXXXXXX

Email:ysyl@bgrimm.com

邮编:100160

地址:北京市南四环西路188号总部基地18区23号楼

关注微信公众号