###
有色金属(冶炼部分):2018,(1):59-63
←前一篇   |   后一篇→
本文二维码信息
码上扫一扫!
高温熔体雾化过程中过热度的数值模拟
王书桓,崔少璞,赵定国,方云楚
(华北理工大学,华北理工大学,华北理工大学,华北理工大学)
Numerical Simulation of Superheat in Atomization of SmFe Melt
wangshuhuan,cuishaopu,zhaodingguo and fangyunchu
(North China University of Science and Technology,,,)
摘要
图/表
参考文献
相似文献
本文已被:浏览 1931次   下载 2363次
投稿时间:2017-07-17     修订日期:2017-07-24     录用日期:2017-07-25     网络发布日期:2017-12-20
中文摘要: 基于紧耦合气雾化喷嘴,运用Fluent软件对高温熔体雾化过程进行数值模拟,分析过热度对高温熔体雾化液滴凝固前飞行距离和液滴破碎程度的影响。结果表明,当过热度增大时,液滴的平均直径(SMD)有减小的趋势,有利于细化雾化颗粒的粒径;液滴的凝固前飞行距离相对比较平缓,中间有小幅的升高趋势。当过热度达到100 ℃时,液滴的破碎比较充分,颗粒的平均直径满足生产的要求,熔体进行雾化后,其平均直径为52.886 μm,液滴的飞行距离为32.68 mm。
Abstract:Based on structure of close-coupled nozzle, atomization process of high temperature melt was simulated with Fluent Soft to investigate influence of superheat on flight distance of atomized droplets before solidification and droplet breakup degree. The results show that it is beneficial to refine particle size of atomized particles when the average diameter (SMD) drops with rise of superheat. Flight distance of droplets before solidification is relatively flat with a slight rise in this progress. When superheat reaches 100 ℃, breakup of droplets is relatively sufficient, and the average diameter of particles meets production requirements. Average diameter of particles is 52.886 μm, and flight distance of droplets before solidification is 32.68 mm after atomization of melt.
文章编号:     中图分类号:    文献标志码:
基金项目:国家自然科学基金资助项目(51574104)
引用文本:
王书桓,崔少璞,赵定国,方云楚.高温熔体雾化过程中过热度的数值模拟[J].有色金属(冶炼部分),2018(1):59-63.
wangshuhuan,cuishaopu,zhaodingguo,fangyunchu.Numerical Simulation of Superheat in Atomization of SmFe Melt[J].Nonferrous Metals (Extractive Metallurgy),2018(1):59-63.

我们一直在努力打
造,精品期刊,传
播学术成果

全国咨询服务热线
86-10-63299752/63299758

联系我们

电话:010-63299752/63299758

传真:010-63299744

QQ:XXXXXXX

Email:ysyl@bgrimm.com

邮编:100160

地址:北京市南四环西路188号总部基地18区23号楼

关注微信公众号