本文已被:浏览 2055次 下载 2067次
投稿时间:2017-03-06 修订日期:2017-03-08 录用日期:2017-03-10 网络发布日期:2017-06-19
投稿时间:2017-03-06 修订日期:2017-03-08 录用日期:2017-03-10 网络发布日期:2017-06-19
中文摘要: 采用FFC熔盐电解法,在900 ℃和2.6~3.2 V槽电压的条件下,以CaCl2熔盐为电解质电解还原高钛渣/SiO2复合阴极,成功制备出了Ti5Si3合金。通过热力学计算和单因素条件试验探讨了电解时间和槽电压对电解产物的影响。结果表明,在初始阶段反应速率很快,随着中间产物CaTiO3和CaSiO3的生成,反应速率逐渐减缓。当槽电压为2.6 V时,反应速率缓慢;提高到2.8 V后,反应速率有了明显的提升。在900 ℃、8 h、3.2 V的条件下制备出的Ti5Si3为疏松多孔、粒径为2~5 μm的合金粉末。
Abstract:Porous Ti5Si3 alloy was prepared from Ti-enriched slag/SiO2 mixed pellet by FFC method in CaCl2 molten salt at 900 ℃ with cell voltage of 2.6~3.2 V. The effects of electrolysis time and cell voltage on electrolysis were investigated by thermodynamics analysis and single factor experiments. The results show that reaction rate is high in initial period, and slows down due to formation of intermediates of CaTiO3 and CaSiO3. The reaction rate is low at cell voltage of 2.6 V, but grows high obviously at 2.8 V. Porous Ti5Si alloy with particle size of 2~5 μm is obtained under the condition of 900 ℃, 8 h, and 3.2 V.
文章编号: 中图分类号: 文献标志码:
基金项目:国家自然科学基金资助项目(51274108)
引用文本:
况文浩,华一新,徐存英,李坚,李艳,张臻,高小兵.CaCl2熔盐中电解高钛渣/SiO2复合阴极制备Ti5Si3的研究[J].有色金属(冶炼部分),2017(7):52-57.
Kuang Wenhao,Hua Yixin,Xu Cunying,Li Jian,Li Yan,Zhang Zhen,Gao Xiaobing.Preparation of Ti5Si3 Alloy by Electrolysis Ti-enriched Slag/SiO2 Composite Cathode in CaCl2 Molten Salt[J].Nonferrous Metals (Extractive Metallurgy),2017(7):52-57.
况文浩,华一新,徐存英,李坚,李艳,张臻,高小兵.CaCl2熔盐中电解高钛渣/SiO2复合阴极制备Ti5Si3的研究[J].有色金属(冶炼部分),2017(7):52-57.
Kuang Wenhao,Hua Yixin,Xu Cunying,Li Jian,Li Yan,Zhang Zhen,Gao Xiaobing.Preparation of Ti5Si3 Alloy by Electrolysis Ti-enriched Slag/SiO2 Composite Cathode in CaCl2 Molten Salt[J].Nonferrous Metals (Extractive Metallurgy),2017(7):52-57.

关注微信公众号