本文已被:浏览 2620次 下载 1986次
投稿时间:2017-02-27 修订日期:2017-03-01 录用日期:2017-03-03 网络发布日期:2017-06-19
投稿时间:2017-02-27 修订日期:2017-03-01 录用日期:2017-03-03 网络发布日期:2017-06-19
中文摘要: 采用镍钴锰三元前驱体废料和草酸钴废料联合氧化还原浸出,研究了三元前驱体废料和草酸钴废料的质量配比、初始酸度、反应温度、反应时间等对镍、钴和锰浸出率的影响。结果表明,最佳反应条件为:三元前驱体废料和草酸钴废料的质量比5︰3.5、初始酸度4 mol/L、反应温度50 ℃、液固比4︰1、反应时间120 min,钴、镍和锰的浸出率分别达到96.76%、99.75%和99.80%,浸出液直接用于共沉淀法制备三元前驱体。实现了两种废料同时浸出和循环回收利用的目的。
Abstract:Ni-Co-Mn ternary precursor (NixCoyMn(1-x-y)(OH)2) waste and cobalt oxalate (CoC2O4) waste were integrated leached. Effects of mass ratio of (NixCoyMn(1-x-y)(OH)2) and CoC2O4 waste, initial acidity, reaction temperature, L/S, and reaction time on leaching rate of Ni, Co, and Mn were investigated. The results show that leaching rate of Ni, Co, and Mn is 99.75%, 96.76%, and 99.80%, respectively under the optimum conditions including mass ratio of (NixCoyMn(1-x-y)(OH)2) and CoC2O4 waste of 5︰3.5, initial acidity of 4 mol/L, reaction temperature of 50 ℃, L/S of 4︰1, and reaction time of 120 min. Lixivium can be used to prepare NixCoyMn(1-x-y)(OH)2 directly. Objective to integrate leaching and comprehensive recycling of two wastes is realized.
文章编号: 中图分类号:TF811; TF816 文献标志码:
基金项目:广东省第十五批省级企业技术中心专项资金资助项目(粤经信创新函[2015]629号);广东省第六批博士后创新实践基地补助经费资助项目(粤人社[2016]85号)
| 作者 | 单位 | |
| 李文津 | 广东佳纳能源科技有限公司 | liwenjin@jycmetal.com |
| 吴理觉 | 广东佳纳能源科技有限公司 | 1523452141@qq.com |
| 付海阔* | 广东佳纳能源科技有限公司 | fuhaikuo@jycmetal.com |
| Author Name | Affiliation | |
| LI Wen-jin | Guangdong Jiana Energy Technology Co.Ltd. | liwenjin@jycmetal.com |
| WU Li-jue | 1523452141@qq.com | |
| FU Hai-kuo | fuhaikuo@jycmetal.com |
引用文本:
李文津,吴理觉,付海阔.镍钴锰三元前驱体废料与草酸钴废料的联合浸出[J].有色金属(冶炼部分),2017(7):7-10.
LI Wen-jin,WU Li-jue,FU Hai-kuo.Integrated Leaching of Waste of Ni-Co-Mn Ternary Precursor and Cobalt Oxalate[J].Nonferrous Metals (Extractive Metallurgy),2017(7):7-10.
李文津,吴理觉,付海阔.镍钴锰三元前驱体废料与草酸钴废料的联合浸出[J].有色金属(冶炼部分),2017(7):7-10.
LI Wen-jin,WU Li-jue,FU Hai-kuo.Integrated Leaching of Waste of Ni-Co-Mn Ternary Precursor and Cobalt Oxalate[J].Nonferrous Metals (Extractive Metallurgy),2017(7):7-10.

关注微信公众号