本文已被:浏览 2217次 下载 2655次
投稿时间:2017-02-15 修订日期:2017-02-22 录用日期:2017-02-23 网络发布日期:2017-05-19
投稿时间:2017-02-15 修订日期:2017-02-22 录用日期:2017-02-23 网络发布日期:2017-05-19
中文摘要: 使用激光熔覆制作了单相组成的Al3Ti3CoCrCu0.5FeMoNi合金涂层,通过退火处理使基体相析出二元金属间化合物,使用SEM、XRD、显微硬度计分析了涂层的组织形貌、相结构和硬度。结果表明,激光熔覆制得的Al3Ti3CoCrCu0.5FeMoNi涂层由BCC单相组成,显微硬度为905.2 HV;在500 ℃以下退火处理,涂层的相组成不变。700 ℃以上退火,涂层从BCC相中析出二元金属间化合物Al2Ti3相,析出相随退火温度升高逐渐长大。涂层硬度随退火温度的升高先降低后逐渐升高,Al2Ti3相析出导致涂层硬度升高。经过900 ℃退火后,涂层硬度达到938.8 HV,超过了未退火时涂覆态的硬度。
中文关键词: 高熵合金 Al3Ti3CoCrCu0.5FeMoNi 激光熔覆 硬度
Abstract:Al3Ti3CoCrCu0.5FeMoNi alloy coating composed of single phase was synthesized by laser cladding. Two-element intermetallic compound was separated from matrix after annealing. The morphology, phase structure, and micro-hardness of coatings were analyzed by SEM, XRD, and microhardness tester. The results show that Al3Ti3CoCrCu0.5FeMoNi coating prepared by laser cladding is of BCC structure with hardness of 905.2 HV. BCC structure of coating remains when annealed at 500 ℃. After annealed at 700 ℃ above, Al2Ti3 precipitates from BCC parent phase of coating, and size of Al2Ti3 rises with increase of annealing temperature. Hardness value of coating drops firstly and then rises with increase of annealing temperature. Precipitation of Al2Ti3 results in rise of hardness of coating. After annealing at 900 ℃, hardness of coating is 938.8 HV, higher than that of non-annealed.
文章编号: 中图分类号:TG113.25 文献标志码:
基金项目:广东省自然科学基金项目(2014A030313784);江门市科技计划项目(2015~2017)
| 作者 | 单位 | |
| 温立哲 | 江门职业技术学院 | wenlizhe@163.com |
| 黄元盛* | 江门职业技术学院 | nightofgz@163.com |
| Author Name | Affiliation | |
| WEN Lizhe | Material Technology Department,Jiangmen Polytechnic | wenlizhe@163.com |
| HUANG Yuansheng | nightofgz@163.com |
引用文本:
温立哲,黄元盛.Al3Ti3CoCrCu0.5FeMoNi高熵合金激光涂层的研究[J].有色金属(冶炼部分),2017(6):67-70.
WEN Lizhe,HUANG Yuansheng.Study on Laser Coating of Al3Ti3CoCrCu0.5FeMoNi High-entropy Alloy[J].Nonferrous Metals (Extractive Metallurgy),2017(6):67-70.
温立哲,黄元盛.Al3Ti3CoCrCu0.5FeMoNi高熵合金激光涂层的研究[J].有色金属(冶炼部分),2017(6):67-70.
WEN Lizhe,HUANG Yuansheng.Study on Laser Coating of Al3Ti3CoCrCu0.5FeMoNi High-entropy Alloy[J].Nonferrous Metals (Extractive Metallurgy),2017(6):67-70.

关注微信公众号