###
有色金属(冶炼部分):2014,(11):66-69
←前一篇   |   后一篇→
本文二维码信息
码上扫一扫!
回转式螺旋气固换热装置内传热过程的数值模拟
王亭亭,周扬民,罗思义,仪垂杰
(青岛理工大学机械工程学院,青岛理工大学机械工程学院,青岛理工大学机械工程学院,青岛理工大学机械工程学院)
Numerical Simulation of Heat Transfer in Rotary Kiln
WANG Ting-ting,ZHOU Yang-min,LUO Si-yi and YI Chui-jie
(School of mechanical engineering,Qingdao Technological University,,,)
摘要
图/表
参考文献
相似文献
本文已被:浏览 2167次   下载 2663次
投稿时间:2014-08-11     修订日期:2014-09-14     录用日期:2014-09-15     网络发布日期:2014-10-15
中文摘要: 采用自制回转窑换热装置对离心粒化后的高温炉渣颗粒进行余热回收,采用有限元分析软件及欧拉双流体模型对装置内气固两相流场进行数值模拟,研究进风风速及回转窑转速对气固之间换热效率的影响,并通过现场试验对模拟结果进行验证。结果表明,当回转体转速为16 r/min、进风风速为4.31 m/s时,颗粒的离散效果较好,热风温度达1 050 K,此时的换热效果最好,数值模拟与试验结果高度吻合。
Abstract:Self-made rotary heat transfer device was applied to recover waste heat of high temperature centrifugal slag particles. Gas-solid phase flow was simulated by finite element analysis software and Euler model. The effects of inlet air velocity and rotating velocity of rotary kiln on heat transfer rate were investigated. The simulated result was verified by field test. The results show that the optimum heat transfer and dispersing effect are obtained under the conditions including rotator velocity of 16 r/min and inlet air velocity of 4.31 m/s with hot air temperature of 1 050 K. Numerical simulation results highly coincide to experimental study.
文章编号:     中图分类号:    文献标志码:
基金项目:国家自然科学基金重点项目资助(50934010);青岛市科技计划项目(13-1-4-175-jch,KJZD-12-55-jch)
引用文本:
王亭亭,周扬民,罗思义,仪垂杰.回转式螺旋气固换热装置内传热过程的数值模拟[J].有色金属(冶炼部分),2014(11):66-69.
WANG Ting-ting,ZHOU Yang-min,LUO Si-yi,YI Chui-jie.Numerical Simulation of Heat Transfer in Rotary Kiln[J].Nonferrous Metals (Extractive Metallurgy),2014(11):66-69.

我们一直在努力打
造,精品期刊,传
播学术成果

全国咨询服务热线
86-10-63299752/63299758

联系我们

电话:010-63299752/63299758

传真:010-63299744

QQ:XXXXXXX

Email:ysyl@bgrimm.com

邮编:100160

地址:北京市南四环西路188号总部基地18区23号楼

关注微信公众号