###
有色金属(冶炼部分):2012,(10):34-37
←前一篇   |   后一篇→
本文二维码信息
码上扫一扫!
热处理时间和压制密度对氮化钽粉电性能的影响
刘莲云,马春红,黄凯,朱鸿民
(1.北京科技大学冶金与生态工程学院; 2.北京交通大学理学院,北京科技大学冶金与生态工程学院,北京科技大学冶金与生态工程学院,北京科技大学冶金与生态工程学院)
Effect of Heat Treatment Time and Green Density on Electrical Characteristics of Tantalum Nitride Powders
Liu Lianyun,Ma chunhong,Huang Kai and Zhu Hongmin
(1.School of Metallurgical and Ecological Engineering,University of Science and Technology Beijing;2.School of Science, Beijing Jiaotong University,,,)
摘要
图/表
参考文献
相似文献
本文已被:浏览 2810次   下载 2326次
投稿时间:2012-03-14     修订日期:2012-03-14     录用日期:2012-03-14     网络发布日期:2012-09-19
中文摘要: 用均相钠还原得到的纳米氮化钽粉在1 350 ℃进行不同时间的热处理,热处理后的粉末制成烧结体并进行阳极氧化过程。通过XRD和场发射扫描电镜分析了粉末的物相结构和形貌,研究了热处理时间和压制密度对氮化钽粉末电性能的影响。结果表明:热处理温度为1 350 ℃、热处理时间40 min、压制密度约4 g/cm时氮化钽阳极块体有较高的比容和较低的漏电流常数。
Abstract:The tantalum nitride nanopowders synthesized by homogenous sodium reduction were annealed at 1 350 ℃ for different durations. The sintered blocks were electrochemically oxidized. The phase structure and microstructure of sintered powders were analyzed with XRD and FESEM. The effects of annealing time and green density on electrical characteristics of powders were studied. The results show that the sintered anode blocks present high CV and low current leakage when annealed at 1 350 ℃ for 40 min with the green density of the powders of 4 g/cm3.
文章编号:     中图分类号:    文献标志码:
基金项目:国家自然科学基金资助项目(51004008,21071014);国家基础研究发展计划(973计划)资助项目(2007CB613301)
引用文本:
刘莲云,马春红,黄凯,朱鸿民.热处理时间和压制密度对氮化钽粉电性能的影响[J].有色金属(冶炼部分),2012(10):34-37.
Liu Lianyun,Ma chunhong,Huang Kai,Zhu Hongmin.Effect of Heat Treatment Time and Green Density on Electrical Characteristics of Tantalum Nitride Powders[J].Nonferrous Metals (Extractive Metallurgy),2012(10):34-37.

我们一直在努力打
造,精品期刊,传
播学术成果

全国咨询服务热线
86-10-63299752/63299758

联系我们

电话:010-63299752/63299758

传真:010-63299744

QQ:XXXXXXX

Email:ysyl@bgrimm.com

邮编:100160

地址:北京市南四环西路188号总部基地18区23号楼

关注微信公众号